Synthesis of everything starting from models

Chapter 12 The amazing printer (please give me a vote for reading!)

Just when he was looking at the camera in his hand, a light curtain appeared from above the camera.

[Item: 3D printer high-definition stereotaxic lens, can continue to be synthesized, pixel accuracy is 50 microns! 】

Seeing the information displayed on the light screen, Li Ao felt more confident. Judging from the current situation, he would definitely make a qualitative leap after upgrading the printer.

He just didn't know what kind of printer he would end up with. With this thought in mind, Li Anchor put the synthesized lens aside, and he continued to synthesize other parts of the printer one by one.

Things like stepper motors, motion tracks, printing platforms, etc., as long as they are the same things on the printer, are all within the scope of his synthesis.

As time went by, he synthesized the parts of the printer one by one.

The stepper motor has now become a high-power and high-precision stepper motor. The running track has also increased in accuracy due to synthesis, and the melting nozzle has also greatly improved in accuracy due to synthesis.

Just now, a whole room of printer parts was spread out, but now the space is reduced by one-third due to synthesis.

At this moment, in front of Li Anchor, there were two completely different sets of printer parts, one was a prototype, and the other was a set synthesized from the two sets.

The synthesized set looks obviously larger than the prototype. For example, the current printing platform. The original printing platform was only 900 square centimeters, but now it has directly become 10000 square centimeters, which is 11 times the area of ​​the prototype printer. many.

If it says that this platform is used, the maximum size can print things up to 1.4 meters long, and this printer can print some parts that are not too large.

Originally it could only be regarded as a small 3D printer, but now it has been directly promoted to a medium and large 3D printer. This is really an unexpected surprise.

With this printer, some things that could not be printed on previous printers can now be printed.

Li Ao is now full of expectations for the synthesized printer. Now just looking at the parts, he can imagine how powerful the printer will be.

He tried hard to control himself not to get excited, and then based on his past experience, he assembled the synthesized 3D printer part by part.

A 3D printer covering an area of ​​one cubic meter appeared in front of Li Anchor.

Today's printers are hard to tell at all. The prototype of this 3D printer was actually a printer that cost less than 3000 yuan.

Li Anchor watched himself synthesize and assemble the printer, and couldn't help but feel excited. A printer of this level could already keep up with hundreds of thousands of industrial-grade printers.

After calming down his excitement, Li Anchor looked for it from the drawer of his computer desk that kept electronic files. Then Li Anchor came to the printer with a USB flash drive marked with a 1:72 static J20 aviation model.

Then the assembled printer was immediately powered on. When the power was plugged in and Li Anchor pressed the power button, the printer immediately started a power-on self-test.

Under the guidance of the positioning lens, powered by a high-precision stepper motor and driven by a high-precision ball screw, the nozzle began to rush left and right on the printing platform with a size of 1 square meter, and it was quickly completed. Self-check, the lens and nozzle are all reset to zero.

All of this happened very quickly, and the self-test ran very smoothly. Although the synthesized printer was still a fused deposition 3D printer, Li Ao always felt that the synthesized one There will be an unexpected effect.When the self-test was completed, Li Anchor couldn't wait to insert the USB flash drive he was holding into the 3D printer, and then the printer's small screen showed that the printing drawings had been recognized.

But just when Li Anchang wanted to start the printer and start printing, an error message appeared on the small screen.

After seeing this error message, Li Anchor was immediately stunned, and couldn't help but think in his heart, it must be that the synthesized printer did not synthesize the system together.

After carefully reading the error message, Li Ao's heart immediately dropped.

The error prompted is nothing else, but that the current print file is not applicable to this printer. As long as the print file is successfully layered and sliced ​​on this printer, printing can actually start.

Li Anchor quickly started operating on the printer, and then a progress bar appeared on the small screen, showing the speed of slicing the file.

The progress bar quickly reached 100%, and then the printer actually started running under Li Anchor's operation.

I saw that the printer's nozzle was constantly running rapidly on the ball screw, driven by the stepper motor.

The speed of the nozzle was so fast that Li Ao could even see the afterimage of the nozzle!
This kind of printing speed really shocked Li Anchor, but at the same time, he couldn't help but worry about whether such a speed would affect the printing quality.

But he soon put this worry aside, because in the short period of time he was thinking about it, some parts of the printing platform had already been printed.

Just looking at the printed part, Li Ao knew it was stable. This time it was really stable, because the printed texture on this printed part was almost comparable to the effect of light-curing printing.

Such an effect made Li Ao feel extremely happy, which meant that he was one step closer to completing the million-profit order!
The printer is still running and printing at a very fast speed.

For the part that has been printed now, if I put it on my previous stereolithography printer, it would take at least more than 40 minutes to print.

But what is the situation now? From the beginning to the present, it only takes less than 5 minutes to complete the calculation. This is eight times the original speed. It is really fast.

This is like when you are playing Vice City and use cheats to speed up the mission because it feels too slow.

While Li Anchor was thinking this, he did not move his eyes away from the model being printed. Looking at the almost invisible printing layer patterns, he knew that he was safe this time.

The fused deposition printer can print things with the same accuracy as those produced by stereolithography, and it is eight times faster than stereolithography. What kind of bicycle is this?
Li Anchor kept staring at the operation of the printer, not feeling bored at all, because it represented nothing else, it was money and wealth, every minute.

As the printer beeped and the printer stopped running, Li Ao couldn't wait to open the printer's protective cover.

He didn't care whether the newly created model had solidified or whether it would burn him, he just touched the model directly.

(End of this chapter)