Countercurrent 1982

Chapter 38 The butt decides the head
After going home and resting in bed for more than two hours, Duan Yun's previous alcoholism had completely disappeared.

In his previous life, Duan Yun didn't drink much, but now this body obviously has a decent amount of alcohol.

Originally, Duan Yun planned to drink only one cup just now, but later, the more he talked with Li Guosheng, the more speculative he became, and the two of them drank a bottle of wine upside down.

In the previous life, Duan Yun would have to go home and 'lay the corpse' almost [-]%, but now he can rest for a while and go to the toilet at most, and he is no longer drunk.

After washing his face in the water room, he immediately felt much refreshed. Carrying a lunch box and riding a bicycle, Duan Yun went to the workshop to work the night shift.

Putting on his work clothes, Duan Yun looked at the empty workstation, feeling somewhat lost.

In any case, when Master Han Zhong was there, he didn't need to worry about many things, but now that he has taken up the post independently, he suddenly has some unspeakable pressure.

If you want to gain a firm foothold in this workshop and gain the attention and favor of leaders, technology and workload are rigid standards.

Although as an apprentice, no one has looked down on him now, but Duan Yun's character has always been very strong. In his previous life, whether in school or in the unit, even if he couldn't be top-notch, at least he had to reach the level of excellence.

After taking out the goggles from the toolbox and wearing them, Duan Yun started the lathe and first processed a stigma to warm up.

At this time, Huang Haitao, the monitor, came over.

Today is Duan Yun's first day on the job. As the squad leader, Huang Haitao must first pay attention to it.

"Squad Leader Huang..." After Duan Yun turned his head to see Huang Haitao, he greeted him with a smile.

"Don't look at me, look at the workpiece!" Huang Haitao signaled Duan Yun not to be distracted.

Huang Haitao actually doesn't care how many workpieces Duan Yun can process in a day. What he attaches the most to is production safety.

Although state-owned enterprises can make a living and earn money for doing more and less, they are very strict about production safety.

Many young employees on night shifts like to wander around during the day and do not make up for sleep. When they go to work at night, they are all groggy and severely lacking in energy.

This is often the time when accidents are most likely to occur.

But at this time, Huang Haitao saw that Duan Yun looked very energetic, and his expression was very serious when machining parts, and his face suddenly eased.

After watching Duan Yun process three stigmas in a row, Huang Haitao picked up the vernier card and checked it out. After all passed, he settled down for two more sentences and left with confidence.

Seeing Huang Haitao leave, Duan Yun turned around and opened the bottom layer of the toolbox, took out the modified parts and servo motors, and quickly installed them.

Re-applied some butter on the gear connection, Duan Yun wiped the handle with a rag, and then added the inclined angle iron to neatly place the blanks to be processed. After replacing the spring chuck, the lathe was started again.

"Buzz!"

With the humming sound of the fast turning of the lathe spindle, the linkage was quickly fixed on the spring chuck after the first hair fitting was rolled down to the chuck.

The two servo motors are started at the same time, the sharp turning tool accurately enters the designated position, and the coolant covers the tool head for the first time.

"squeak!"

The blue-black iron filings slipped from the workpiece, revealing a bright metallic luster.

It only took about 1 minute, and the first workpiece has been processed.

Duan Yun breathed a sigh of relief when he saw that the second workpiece was automatically loaded into the chuck.

After entering the automatic processing, Duan Yun was freed from the workstation.

All he has to do now is add stock to the angle iron frame and replace the worn bits.

At this time, Yun did not completely idle, but stood in front of the tool cabinet, took out paper and pen, and began to write and draw on it.

In Duan Yun's opinion, the automation device he is using now still has some room for modification, but due to the inherently slow speed of the lathe spindle, the efficiency of the re-modification will not be greatly improved, so Duan Yun I began to think about other lathes in the factory.

Duan Yun is quite familiar with other lathes in use in the factory.

When Duan Yun worked at the Northern Locomotive Factory in his previous life, there were lathes produced by the Eighteen Luohans in the Northeast. Duan Yun's original lathe skills were actually developed on these lathes.

Perhaps a layman may find it inconceivable that domestic factories in later generations still use this kind of domestic lathes in the 80s and 80s, but the reality is that even when Duan Yun was working in a locomotive factory, the penetration rate of digital machine tools in domestic enterprises was still not high. , It is not even up to the popularization level of developed countries in Europe, America and Japan in the [-]s and [-]s. Many high-end CNC machine tools can only completely rely on imports. This is a situation that sounds depressing but is true.

Duan Yun is currently incapable and has no plans to build a domestic CNC lathe at this time of year. This is simply unrealistic. However, Duan Yun can still easily do it by modifying a domestic ordinary lathe to improve the processing efficiency.

In fact, when Duan Yun was in the factory in his previous life, he proposed a modification plan for this kind of domestic lathe, but it was all rejected in the end.

In fact, now Duan Yun thinks that he was indeed a little naive at the beginning. He had no problem with the technology of modifying the lathe, but he did not consider the reality of the factory at that time.

As the so-called butt decides the head, leaders and workers have different perspectives on problems.

Just as he wanted to modify the lathe at the locomotive factory, Duan Yun thought about how to improve the production efficiency of the workshop and improve the production process.

What the leader considers is how to arrange the idle workers after the lathe is automated and refitted, especially those senior technicians who are close to the factory leaders and have a long working experience. How can they continue to get the high wages in the factory? These are all things that will give them headaches, so it is better to have less than one more thing, and put Duan Yun's technical transformation plan on the shelf...

So this also reminds Duan Yun that he wants to do any technological transformation in this factory. There is no leader to back up, or the timing is not right. This is exactly what Duan Yun wanted to do before. The main reason to get involved with the secretary line.

In addition, in Duan Yun's view, he still has a good chance to succeed in this kind of technical transformation in the workshop.

When drinking with Li Guosheng in the evening, Duan Yun learned about the current situation of the factory.

Nowadays, the Red Star Gear Factory has received a lot of orders. The two major products of the factory, single hydraulic props and gearbox gears, have reached the level of short supply, and even some units have not been able to get the goods in a short period of time.

On the other hand, the factory has promised to build a batch of new houses this year and next at the workers' congress since last year to relieve the housing pressure of the factory employees. However, the factory's production capacity is limited now. However, the inability to produce too many unplanned products resulted in insufficient self-retained funds for the factory, and the construction of a new house naturally became a distant prospect...

(End of this chapter)